ELASTOMERIC AC5300

Tough Stuff AC5300 is designed to provide long lasting, trouble free systems for the renewal and maintenance for all types of surfaces. The tough, flexible film adheres tenaciously and is resilient enough to absorb expansion and contraction. This coating will work well on metal, wood, tile, slate and stucco.



RECOMMENDED USES

Metal, Slate, Stucco, Wood, Tile, And most other building materials


PRODUCT CHARACTERISTICS
COLOR: White, can be tinted.
VISCOSITY: 2,000-3,000 cps
WEIGHT PER GALLON: 12.0 pounds / gallon
VOC (EPA method 24): Compliant
SHELF LIFE: 12 months unopened
CLEANUP: Water
SOLIDS BY WEIGHT: 58%
SOLIDS BY VOLUME: 42%
RECOMMENDED SPREADING RATE PER COAT: 250 square feet / gallon

Drying Schedule: At 8 mils wet & 50% Relative Humidity:

  50°F 70°F 110°F
To Touch 90 min. 30 min. 15 min.
To Recoat 1 day 6 hours 4 hours
To Cure 30 days 15 days 10 days

Drying time is temperature, humidity, and film thickness dependent. DO NOT apply when the dew point is less than 5°

F above ambient temperature.


APPLICATION PROCEDURES
  • This product can be sprayed, brushed, or rolled on.
  • When using airless spray equipment, it is recommended that a reversible spray tip be used with an orifice of .017 to 0.24 and minimum 40 degree fan angle.
  • Material should be applied to a 4 - 12 mil thickness depending upon porosity of substrate
  • Mix material is separated.
  • Please consult the Coatings International Technical Department with specific application questions.
PERFORMANCE TIPS
  • DO NOT THIN
  • POWER MIX BEFORE USING
  • On porous surfaces allow to cure four hours.
  • All loose rust and scale should be removed.
  • Rusty areas should be saturated without leaving any excess material.
  • Puddles may blister the finish coat if not cured before coating.
  • Recoat within one hour in good weather.
  • AC5300 has no recoat window but dirt that accumulates on the material will have to be removed.
  • Do not allow containers to freeze.
CLEANUP INSTRUCTIONS

Clean spills and spatters immediately with water
Clean hands and tools immediately after use with soapy water.
After cleaning, flush spray equipment with water followed by mineral spirits. Leave mineral spirits in the line to prevent rusting.

SAFETY PRECAUTIONS

INSTALLERS must read and understand all technical and informational literature for Tough Stuff AC5300, including the Material Safety Data Sheets, prior to using this product.

For chemical emergencies, spills, leaks, exposure, or accidents in the U.S.: CALL CHEMTREC 24 HOURS A DAY / 365 DAYS A YEAR 1-800-424-9300.

ORDERING INFORMATION

Packaging:

Container Size Weight Class
5 gallon cans 60 lbs. 55
55 gallon drum 660 lbs. 55

DOT Shipping Information:
Nonhazardous

HMIS:
Health 1, Flammability 0, Reactivity 0, Protection B

Published technical data and instructions are subject to change without notice. Please contact your Coatings International Roofing Systems representative for the most current information.

Revised November 2003

Important: The information in this MSDS was obtained from sources which we believe are reliable. HOWEVER, THE INFORMATION IS PROVIDED WITHOUT ANY WARRANTY, EXPRESSED, OR IMPLIED, REGARDING ITS CORRECTNESS.

The conditions or methods of handling, storage, use and disposal of the product are beyond our control, and may be beyond our knowledge. FOR THIS AND OTHER REASONS, WE DO NOT ASSUME RESPONSIBILITY AND EXPRESSLY DISCLAIM LIABILITY FOR LOSS, DAMAGE, OR EXPENSE ARISING OUT OF OR IN ANY WAY CONNECTED WITH THE HANDLING, STORAGE, USE, OR DISPOSAL OF THE PRODUCT.

This MSDS was prepared and is to be used only for this product. If apprised of changes, updated MSDS sheets will be promptly issued. Users must make their own determination regarding the suitability of the product for their own purpose prior to use.

VIEW / DOWNLOAD a printable PDF version of this document.

SECTION I - MATERIAL IDENTIFICATION AND INFORMATION

Components - Chemical Name & Common Names(Hazardous Components 1% or greater: Carcinogens 0.1% or greater)

CHEMICAL NAME (COMMON NAME) CAS # % OSHA PEL (PPM) ACGIH TLV (PPM) OTHER LIMITS RECOMMENDED
Acrylic Polymer NONHAZ 29.0 N/A    
Residual Monomers   0.2 max N/A    
Ammonia   0.2 max 25 50 25
Water NONHAZ 48.0      

SECTION II - PHYSICAL/CHEMICAL CHARACTERISTICS
1) BOILING POINT
212°F / 100°C
2) SPECIFIC GRAVITY (Water = 1) 1.2
3) VAPOR PRESSURE (mm Hg at 20°F): <17
4) MELTING POINT 0°C / 32°F
5) VAPOR DENSITY (air = 1) > 1 (heavier than air)
6) EVAPORATION RATE < 1 / Slower than Ether
7) SOLUBILITY IN WATER Dilutable
8) WATER REACTIVE N/A
9) APPEARANCE & ODOR White liquid; slight ammoniacal odor; pil 9.5 - 10.0

SECTION III - FIRE AND EXPLOSION DATA
  1. FLASH POINT & METHOD:

    Noncombustible

  2. AUTO-IGNITION TEMPERATURE:

    N/A

  3. FLAMMABILITY LIMITS IN AIR % BY VOLUME:

    LEL: N/A UEL: N/A

  4. EXTINGUISHER (MEDIA):

    N/A

  5. SPECIAL FIRE FIGHTING PROCEDURES:

    N/A

  6. UNUSUAL FIRE AND EXPLOSION HAZARDS:

    Product will not burn but may splatter if temperature exceeds boiling point. Polymer films are capable of burning giving off oxides or carbon/nitrogen.


SECTION IV - REACTIVITY HAZARD DATA
  1. STABILITY:

    Stable

  2. CONDITIONS TO AVOID:

    N/A

  3. INCOMPATIBILITY (Materials to Avoid):

    N/A

  4. HAZARDOUS DECOMPOSITION PRODUCTS:

    N/A

  5. HAZARDOUS POLYMERIZATION:

    Will not occur


SECTION V - HEALTH HAZARD DATA
  1. PRIMARY ROUTES OF ENTRY:
    1. Inhalation-Yes
    2. Skin absorption-N/A
    3. Ingestion-N/A
  2. CARCINOGEN LISTED IN:
    1. NTP - no
    2. IARC MONOGRAPH - no
    3. OSHA - Not Listed
  3. HEALTH HAZARDS:
    1. ACUTE: N/A
    2. CHRONIC: N/A
  4. SIGNS AND SYMPTOMS OF EXPOSURE:

    INHALATION: Adverse health effects from vapors or spray mists in poorly ventilated areas may include irritation of the mucous membranes of the nose, throat and respiratory tract and symptoms of headache and nausea.

    SKIN CONTACT: Prolonged or repeated contact with the product may cause skin irritation.

    EYE CONTACT: Direct contact may product eye irritation.

  5. MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:

    N/A

  6. EMERGENCY FIRST AID PROCEDURES:

    Seek medical assistance for further treatment, observation and support if necessary.

  7. EYE CONTACT:

    Promptly & thoroughly wash eyes with water for at least 15 minutes and consult physician if irritation persists; wash skin thoroughly with soap and water; if drenched, remove & wash clothing before reuse.

  8. SKIN CONTACT:

    Wash skin thoroughly with soap & water; if drenched, remove & wash clothing before reuse.

  9. INHALATION:

    Move subject to fresh air.

  10. INGESTION:

    If victim is conscious, give 2 glasses water. Call physician immediately. Do not give anything by mouth to an unconscious person.


SECTION VI - CONTROL AND PROTECTIVE MEASURES
  1. RESPIRATORY PROTECTION (Specify type):

    None required if good ventilation is maintained. Otherwise wear MESA/NIOSH approved respirator suitable for vapor or mist concentrations encountered.

  2. PROTECTIVE GLOVES:

    Impervious

  3. EYE PROTECTION:

    Safety glasses.

  4. VENTILATION TO BE USED:
    1. Local exhaust - Yes
    2. Mechanical (general) - recommended
  5. OTHER (Specify):

    Additional local exhaust is recommended where vapors, mist, or aerosols may be released.


SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE/LEAKS
  1. STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED:
    1. Keep unnecessary people away. Dike and contain pill with inert material (sand, earth, etc.) and transfer liquid to containers for recovery or disposal. Keep spill out of sewers and bodies of water. Floors may be slippery, care should be exercised to avoid falls.
  2. WASTE DISPOSAL METHODS:

    Coagulate the emulsion with ferric chloride or sulfate and then lime to a clear end point. Decant the clear liquid to sewer and landfill in coagulum. Incineration of the entire emulsion is possible but impractical because of the high water content. Coagulum may be incinerated.

  3. ENVIRONMENTAL IMPACT:

    N/A

  4. PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:

    Avoid storage above 100°F. Keep from freezing.

    Minimum: 1.1° C/34° F Maximum: 60° C / 140° F

    Avoid prolonged or repeated skin contact. Avoid inhalation of heated vapors or spray mists.

    Revised January 2004